The CPU cooler is an important component in the computer system. This article will tell you How To Remove Cpu Cooler. It is the main part of the cooling system of a computer. One of its primary functions is to keep the processor cool, which keeps your PC running efficiently.

CPUs are found in almost every computer. They make your PC work. There are three major types of CPU: air-cooled, liquid-cooled, and phase-change cooling. 

If your computer is air-cooled, you won’t have to worry about opening up your case to install a new chip. Air-cooling relies on natural convection to move heat away from the processor, but not all systems can use this method.

What is a CPU Cooler?

A CPU cooler is a device that helps reduce the operating temperature of a computer processor by removing heat. These devices can come in many shapes and sizes, but they all work on the same principle

The most common type of CPU cooler is an air-based heatsink with fans that can improve its cooling capacity. This type of cooler is ideal for use with desktop CPUs (Intel, AMD), as well as some laptop CPUs.

While it’s true that a CPU cooler doesn’t require much maintenance before you install one make sure you’re familiar with the installation process. Most importantly, check out these tips on installation and maintenance.

You can also check out this amazing article on Best Cooler For 5900X.

Remove the CPU cooler?

Turn off the computer:

Before you start any process, it is important to make sure that your computer is turned off. This way, you won’t get shocked. Also, your computer will behave differently and components can burn out.

Remove cooler cover:

Some of the CPU cases have a vent on the top. You need to remove it first to make the processor and heatsink visible.

Heating the thermal paste:

If the thermal paste is cold, then it will keep the cooler fan and processor welded together. The trick to do this is to heat your computer for 15-20 minutes.

It will allow the thermal paste to warm up, making it gooey and pliable, which will eventually help you to remove the cooler with ease.

Unclip from the processor

The clip holding the cooler on the motherboard is easy to find. Remove the clip by pulling it gently away from the board and then remove the cooler from the motherboard.

Some coolers might be attached with screws. If your cooler is secured with screws, then unscrew them to remove the cooler. It’s important not to over-tighten screws, or the screws may break or your CPU may get damaged.

How to Install a CPU Cooler?

Installing a CPU cooler is a simple process that generally takes only a few minutes to complete. However, this doesn’t mean it’s easy to do. This article will guide you through the process step-by-step.

The first step in cooling your CPU is to get your case open. The second step is to look for a fan mount for the processor. Once you’ve located the mount, ensure that there are four holes around it where you should attach the fan.


Insert the screws into the corresponding holes around the fan and tighten them so they won’t come loose. Avoid over-tightening the screws or you might strip out one of your motherboard’s screw holes, making it unusable for more serious projects later on.

Place a thin layer of thermal paste on your CPU chip. Thermal paste is usually a small dab in the center of the chip, but too much will only make it harder to remove. The right amount for your chip is just enough to cover the whole chip.

You can connect these two components up inside the case before you put the cover back on. The fan should be connected to a motherboard connector that’s labeled as CPU or something similar, and your heatsink can go into any open memory slot.

After this is done, remove your motherboard’s power cable and plug it into the wall to turn it on for the first time since installing these components inside of it. If all goes well, you will likely hear an extremely loud buzzing noise coming from either where the fans are located or near the processor itself if they’re not plugged up correctly.

You’ll want to quickly unplug everything from your computer for a few seconds. Just in case one of the devices disconnects while you’re working, it’s better to be safe than sorry. Once everything has settled down for a few minutes, you can restart your computer. You may think that a CPU cooler is just something to be tossed onto your motherboard, but don’t assume.


The CPU Cooler is one of the most important components in your computer, so it’s an important task to do when you build or repair computers.

Also check out to know all about the CPU coolers and its related information.

We hope this article on How To Remove CPU Cooler? has helped clear up some confusion about how to remove and replace that pesky cooler for better airflow around in your processor. If you have more questions, feel free to reach out anytime.